Answer:
1.78×10×10^10 electron
Explanation:
Electric field outside the sphere can be calculated using below expression
E= kq/ r^2..........eqn(1)
Where k= 9 × 10^9 NM^2/C^2
q= charge
E= 1440 N/C
Diameter= 30.0 cm= 0.3 m
r= radius= 0.3/2= 0.15m
If we make q subject of formula from eqn(1) we have
q= Er^2/k............eqn(2)
q= 1440 × (0.15)^2 /(9 × 10^9 )
= 2.85×10^-9C
Total charge is an integer of electron charge , then we can calculate the number of the electron using the expression below
q= Ne
Where
N = number of electron
Making N subject of the formula we have
N= q/e
Where e= electron value= 1.6× 10^-19
N=2.85×10^-9 /1.6× 10^-19
= 1.78×10×10^10 electron
Help me please it’s due right now review question help
Answer:
M.E = mgh
given, m=400g = 400/1000=0.4kg
h=1.75m
g=9.81m/s²
M.E =0.4×9.81×1.75
=6.867J
A dog runs 51 m west to fetch a ball and brings it back only 27 m before stopping.
The total displacement of the dog is:
A 3.5 kg object gains 76 J of potential energy as it is lifted vertically. Find the new height of the object?
Answer:
1.72 m
Explanation:
Potential energy = mgh, where m is mass, g is acceleration due to gravity (9.8), and h is height
76 = (3.5)(9.8)h
76=44.1h
h=1.72335600907 ≈1.72 m
Answer:
:r
Explanation:r
Tobnbv346468this Ishmael
In an application, Germanium is
made p-type material by adding
Indium. The rate of adding is one
indium atom
per
3 Germanium
atom. Assume donor density to be
zero and ni = 6.2 Cubic
metre at room temperature.
Determine the value
of
the
aceeptor atom density
Answer:
produce electronics
Explanation:
The uses of Germanium are recorded beneath: Germanium's principle use is to deliver strong state hardware, semiconductors and fiber optic frameworks. As a phosphor in fluorescent lights.
A 85-W lamp is connected to 100 V. What is the resistance of the lamp?
What voltage would be measured across the 15 ohm resistor?
A)
2.5 volts
B)
5.0 volts
C)
7.5 volts
D)
10 volts
Answer:
7.5 volts
Explanation:
I did it on USA Testprep
A 1.65-m-long wire having a mass of 0.100 kg is fixed at both ends. The tension in the wire is maintained at 16.0 N. (a) What are the frequencies of the first three allowed modes of vibration
Answer:
Explanation:
mass per unit length ρ = .100 / 1.65 = .0606 . kg /m
length of wire L = 1.65 m
For fundamental frequency , the expression is as follows
n = [tex]\frac{1}{2L} \sqrt{\frac{T}{m} }[/tex]
L = 1.65 , T = 16 n and m = .0606
n = [tex]\frac{1}{2\times 1.65} \sqrt{\frac{16}{.0606} }[/tex]
= 4.9 /s .
This is fundamental frequency .
other mode of vibration ( first three ) will be as follows
4.9 x 2 = 9.8 /s ,
4.9 x 3 = 14.7 /s .
9.2 True/False Questions
1) Unsatisfying relationships can interfere with your well-being.
Answer:
2) One way to tell if a relationship is unhealthy is that you are unhappy.
Answer:
3) Managers at large companies are more involved in the day-to-day operations of their businesses than entrepreneurs.
Answer:
4) Being an effective member of a team depends entirely on the project's outcome.
Answer:
5) Teams are influenced by the personal qualities of the team members.
Answer:
An object, with mass 64 kg and speed 14 m/s relative to an observer, explodes into two pieces, one 2 times as massive as the other; the explosion takes place in deep space. The less massive piece stops relative to the observer. How much kinetic energy is added to the system during the explosion, as measured in the observer's reference frame
Answer:
K_f = 1881.6 J
Explanation:
To solve this exercise, let's start by finding the velocities of the bodies.
We define a system formed by the initial object and its parts, with this the forces during the explosion are internal and the moment is conserved
initial instant. Before the explosion
p₀ = M v₀
final instant. After the explosion
p_f = m₁ v + m₂ 0
the moeoto is preserved
p₀ = p_f
M v₀ = m₁ v
v = [tex]\frac{m_1}{M}[/tex] v₀
in the exercise they indicate that the most massive part has twice the other part
M = m₁ + m₂
M = 2m₂ + m₂ = 3 m₂
m₂ = M / 3
so the most massive part is worth
m₁ = 2 M / 3
we substitute
v = ⅔ v₀
with the speed of each element we can look for the kinetic energy
initial
K₀ = ½ M v₀²
Final
K_f = ½ m₁ v² + 0
K_f = ½ (⅔ M) (⅔ v₀)²
K_f = [tex]\frac{8}{27}[/tex] (½ M v₀²)
K_f = [tex]\frac{8}{27}[/tex] K₀
the energy added to the system is
ΔK = Kf -K₀
ΔK = (8/27 - 1) K₀
ΔK = -0.7 K₀
K_f = K₀ + ΔK
K_f = K₀ (1 -0.7)
K_f = 0.3 K₀
let's calculate
K_f = 0.3 (½ 64 14²)
K_f = 1881.6 J
4) Which statement about teamwork is not true?
A) Team members should not have to make personal sacrifices for the success of the team.
B) To be successful, all team members need to agree about how to achieve the goal.
C) To achieve agreement, teams must be able to communicate and negotiate.
D) Team members need to be ready to resolve conflicts in an open and honest way
Answer: A) Team should not have to make personal sacrifices for the success of the team.
Explanation:
hhhep faaast plssssss
Answer:
false
Explanation:
I am in need of points sorry
Why is it imperative that the collision takes place in a plane parallel to the plane containing the camera lens
Answer:
It is imperative that the collision takes place in a plane parallel to the plane containing the camera lens so that parallax does not affects the recording of camera.
Explanation:
It is imperative that the collision takes place in a plane parallel to the plane containing the camera lens so that parallax does not affect the recording of the camera. There may occur an error in video analysis if the camera is tilted at an angle in relation to the collision plane.
(The role of the lens is to take light to a fixed focal point.)
What is the approximate surface temperature of the 'White Dwarfs'?.
2,500-5,000 K
5,000-10,000
10,000-15,000 K
15,000 K-35,000 K
Answer:
5,000-10,000 K
Explanation:
make me your brainlist pls
Please help guy review question.
Answer:
66.67 km/h
Explanation:
20 + 30 = 50
50/.75 = 66.67
2) Which of the following is not a quality of a healthy relationship?
A) respect
B) trust
C) closed communication
D) honesty
. Indiana Jones needs to ascend a 10-m-high building. There is a large hose filled with pressurized water hanging down from the building top. He builds a square platform and mounts four 4-cm-diameter nozzles pointing down at each corner. By connecting hose branches, a water jet with a velocity, u, can be produced from each nozzle. Jones, the platform, and the nozzles have a combined mass of 150 kg. Determine the minimum water jet velocity, u (m/s), needed to raise the system.
Answer:
u = 14 m / s
Explanation:
For this exercise let's use conservation of energy
starting point. On the floor just when u speeding out
Em₀ = K = ½ m v²
final point. When on top of the building, no speed
Em_f = U = m g h
energy is conserved
Em₀ = Em_f
½ m v² = m g h
v = u
u = [tex]\sqrt{2 g h}[/tex]
u= [tex]\sqrt{2 \ 9.8 \ 10}[/tex]
u = 14 m / s
The augue
1) What will be number of image if the angle
between two mirroro is
a) 45
b:36
How would increasing the pressure of this reaction affect the equilibrium
Explanation:
c because there is element
Answer:
C. H2 and N2 would react to produce more NH3
Explanation:
A.P.E.X
You are watching a s Saturday morning cartoon concerning a jungle hero called George of the Jungle. George attempts to save a friend, an ape named Ape, from a stampeding herd of wildebeests. Ape is at the base of a tall tree which has a vine attached to its top. George is in another tree holding the other end of the vine. George plans to swing down from the tree, grab Ape at the bottom of the swing, and continue up to safety on a ledge which is half of George's initial height in the tree. Assuming that Ape weights the same as George, will they successfully make it to the top of the ledge? If you believe they do, how high a ledge could they make it to? If you disagree, suggest what could be done for George to save Ape.
Answer:
I don't think so because if Ape was the same weight as george I don't
think he can hold him but maybe so let's say he could hold his own ape then Yes I think he could make it to the ledge Now I think they could make it to the ledge which was half the size.
Sorry if this sounded weird English is my 2nd language Oh and if this helped please give brainiest thank you <3
If this is the stationary wall isn’t the ANSWER that there is no work being done? If not what is the correct answer and why? Help!!
Answer:
no work is done cause there is no movement of the wall
To apply Problem-Solving Strategy 12.2 Sound intensity. You are trying to overhear a most interesting conversation, but from your distance of 10.0 m , it sounds like only an average whisper of 20.0 dB . So you decide to move closer to give the conversation a sound level of 60.0 dB instead. How close should you come
Answer:
r₂ = 0.316 m
Explanation:
The sound level is expressed in decibels, therefore let's find the intensity for the new location
β = 10 log [tex]\frac{I}{I_o}[/tex]
let's write this expression for our case
β₁ = 10 log \frac{I_1}{I_o}
β₂ = 10 log \frac{I_2}{I_o}
β₂ -β₁ = 10 ( [tex]log \frac{I_2}{I_o} - log \frac{I_1}{I_o}[/tex])
β₂ - β₁ = 10 [tex]log \frac{I_2}{I_1}[/tex]
log \frac{I_2}{I_1} = [tex]\frac{60 - 20}{10}[/tex] = 3
[tex]\frac{I_2}{I_1}[/tex] = 10³
I₂ = 10³ I₁
having the relationship between the intensities, we can use the definition of intensity which is the power per unit area
I = P / A
P = I A
the area is of a sphere
A = 4π r²
the power of the sound does not change, so we can write it for the two points
P = I₁ A₁ = I₂ A₂
I₁ r₁² = I₂ r₂²
we substitute the ratio of intensities
I₁ r₁² = (10³ I₁ ) r₂²
r₁² = 10³ r₂²
r₂ = r₁ / √10³
we calculate
r₂ = [tex]\frac{10.0}{\sqrt{10^3} }[/tex]
r₂ = 0.316 m
A uniform magnetic field is in the positive z direction. A positively charged particle is moving in the positive x direction through the field. The net force on the particle can be made zero by applying an electric field in what direction
Answer:
We apply an electric field in the negative y direction
Explanation:
Since A uniform magnetic field is in the positive z direction and A positively charged particle is moving in the positive x direction through the field, the magnetic force acting on the positively charged particle is in the positive y direction according to Fleming's right-hand rule.
For the net force on the particle to be zero, we apply an electric field in the negative y direction to create an electric force on the positively charged particle, so as to cancel out the magnetic force.
Please help me with this question. Every help is appreciated.
Answer:
Change in KE = +1.96×10^4 J while the change in ME = 0 J
Irrigation channels that require regular flow monitoring are often equipped with electromagnetic flowmeters in which the magnetic field is produced by horizontal coils embedded in the bottom of the channel. A particular coil has 100 turns and a diameter of 6.0 m. When it's time for a measurement, a 4.5 A current is turned on. The large diameter of the coil means that the field in the water flowing directly above the center of the coil is approximately equal to the field in the center of the coil. The field is directed downward and the water is flowing east. The water is flowing above the center of the coil at 1.5 m/s
Required:
a. What is the magnitude of the field at the center of the coil?
b. What is the direction of the force on a positive ion in the water above the center of the coil?
Answer:
A) B = 9.425 × 10^(-5) T
B) North direction
Explanation:
A) We are given;
Current in coil; I = 4.5 A
Number of turns; N = 100 turns
Radius;R = diameter/2 = 6/2 = 3 m
Formula for the magnetic field at the center of the coil is given by;
B = (μ_o•N•I)/2R
Where μ_o is a constant = 4π × 10^(-7) H/m
Thus;
B = (4π × 10^(-7) × 100 × 4.5)/(2 × 3)
B = 9.425 × 10^(-5) T
B) The direction of the force on a positive ion in water can be gotten by the application of flemmings right hand rule.
From flemmings right hand rule, we know that;
- The thumb indicates the direction of the motion of the force which is in the north direction.
- The Index finger indicates the direction of the magnetic field which is in the east direction
- The middle finger indicates the direction of magnetic field which is downwards in the west direction.
Therefore, the direction of the force as seen from flemmings right hand rule is in the north direction
I need help with this
need help ASAP!!!!!!!!!!!
Answer:
The equation says that due to variation in temperature is
delt T = .59 m/s / C = 16 C * .59 m/s = 9.44 m/s
So v = 332 m/s + 9.44 m/s = 341 m/s (to three significant figures)
a 4.5 Hz wave has a wavelength of 0.8m. what is the speed
0.18 m/s
5.6m/s
5.3m/s
3.6m/s
Answer:
Explanation
if 400g is 1kg find the ratio in the simplest form
2:5
Explanation:
400g : 1kg
400g: 1000g
4 : 10
2 : 5
A substance whose shape can easily change is a
What is respiration?
Answer:
taking in oxygen and giving out carbon dioxide is called respiration
Answer:
i think that respiratiln is when you breqth